请教TCA襟翼和扰流板设备的设置问题AS320系列

BeiJingAIRK

新入了TCA襟翼和扰流板，襟翼和扰流板在P3D设置页面都设置好，基本可以正常使用。


但起落手柄和停留刹车的设置并不能完美匹配，根本不能识别飞机现在状态和硬件设备的位置匹配，也在configartar里面勾选了TCA


扰流板下面的AUTO BRK旋钮更是不起作用，请问各位大佬，AS321有什么办法可以像FSL系列那样完美匹配吗？感谢！！

叶奕奕奕奕

我记得这些个按键都是要设置在HOTAS General按键的，有一个文件专门讲了这个，我找找看还有没有

叶奕奕奕奕

AS论坛上找到了，复制下来：

To correctly implement those switches/knobs/handles please assign following buttons in the "Key Assignments" menu of P3D:

Switch on game controller	EVENT	ASSIGNMENT	REPEAT slider	ON RELEASE
GEAR lever in UP position	"Hotas generic key (A8)"	BUTTON 21	full left	-
GEAR lever in DOWN position	"Hotas generic key (A9)"	BUTTON 21	-	YES
PARK BRK handle in SET position	"Hotas generic key (B0)"	BUTTON 20	full left	-
PARK BRK handle in RELEASE position	"Hotas generic key (B1)"	BUTTON 20	-	YES
AUTO BRK BTV	"Hotas generic key (B2)"	BUTTON 22	full left	-
AUTO BRK LO	"Hotas generic key (B3)"	BUTTON 23	full left	-
AUTO BRK 2	"Hotas generic key (B4)"	BUTTON 24	full left	-
AUTO BKR HI	"Hotas generic key (B5)"	BUTTON 26	full left	-
RUD TRIM knob in left position	"Hotas generic key (B6)"	BUTTON 18	middle	-
RUD TRIM knob in right position	"Hotas generic key (B7)"	BUTTON 19	middle	-
RUD TRIM knob in center position	"Hotas generic key (B8)"	BUTTON 18	-	YES
RUD TRIM knob in center position	"Hotas generic key (B8)"	BUTTON 19	-	YES
RUD TRIM RESET button	"Hotas generic key (B9)"	BUTTON 17	full left	-
RUD TRIM RESET button	"Hotas generic key (B9)"	BUTTON 17	-	YES

To do so please follow follong steps (as an example for GEAR lever switch):

• Enter "hotas" into the search field on the top right of the key assignment menu
• Click on "Hotas generig key (A8)", then click "New" at the bottom of the window. The "New Assignment" window opens.
• Move the GEAR lever on your controller into "UP" position, "Button 21" should show up in the text field. Then click OK.
• Leave the "Repeat" slider on the left side
• Now click on "Hotas generig key (A9)" and again click "New" at the bottom of the window. Again, the "New Assignment" window opens.
• Move the GEAR lever on your controller into "DOWN" position, "Button 21" should show up in the text field. Then click OK.
• Select "On Release", then click OK.
  

Assign all above mentioned switches in the same way...

BeiJingAIRK

叶奕奕奕奕 发表于 2021-12-14 01:30
AS论坛上找到了，复制下来：

To correctly implement those switches/knobs/handles please assign follow ...

哇，这个真的好，太感谢了！

AIRWINGS

老哥你好，请教一下P3D，襟翼和扰流板控制台的设置，我的进去后没有自动识别，机型是AS320，感谢🙏